IP address conflicts occur when two or more devices on the same network are assigned the same IP address. An IP address is a unique identifier for devices like computers and laptops. It consists of a series of numbers, for instance, 192.168.8.4. One cannot have access to the internet without it. An error or warning message will display on your screen. It will inform you of an resolve problem of IP address. The devices with this problem can’t connect to the network. So, they can’t perform any network operations.

Types of IP Address Conflicts

IP address conflicts typically fall into two categories:

• Static IP address dispute: A static IP address conflict arises when a network administrator assigns the same IP address to two devices. It also occurs when a device in the DHCP range is assigned an IP address that is fixed. The allocated addresses will clash with this.
• Dynamic IP address conflict: Two devices are given the same IP address by a DHCP server. Server problems, expired leases, and wrong configurations might all be the cause of this.

This problem can also arise because of the following reasons mentioned:

• A computer is allocated an inactive IP address in the DHCP range for the local area network. The DHCP server has assigned the same address to a computer.

• The device is put into sleep mode. When it turns on, it connects to a different network. That network has the same IP address as another computer.

• If you have many network adapters, they might conflict. They may have the same IP address.

• If you have multiple wireless routers on your network, and DHCP is enabled on more than one,

To fix this error, you can try the following solutions:

Solution1: Resolve problem of IP address 

• Try to release and renew the IP address of your device using the Command Prompt. You need to click on Start and then type in cmd.

• In the next step, you need to enter the command to release your IP address:

ipconfig /release

You’ll get several results from the command above, depending on how many adapters you have. For Ethernet ports, you’ll see the Ethernet adapter Ethernet x. For wireless cards, you’ll see Wireless LAN Adapter Wi-Fi, etc.

But, if your device has a static IP, the operation will fail. None of the adapters are permitted for this operation. In this case, you need to skip down to the Reconfigure Static IP Address section.

• After running this command, you must also run the command to renew the IP address from the DHCP server.

• Wait for a few seconds; you will see the results, and there should be an IP address listed next to the IPv4 address.

Solution 2: Reconfigure Static IP Address

If your device is using an IP address that is static in nature. This might create an IP address conflict; you can try to change your IP address. To do so, you need to follow the steps:

• Firstly, click on the control panel and go to the icons. Now, you need to click on the option of “Network and Sharing Center” that you can find on the left-hand side.

• In the next step, you need to click on the option for “Change Adapter Settings.”

• Now, right-click on the “Network Adapter” used for the Internet. Then, select “Properties.”

• In the next step, select Internet Protocol Version 4 (TCP/IPv4), and then click on the Properties button. From there, automatically obtain the IP address from a DHCP server.

If these two solutions don’t solve your problem, the issue might be related to your router.

Solution 3: Wireless Routers

Another solution to resolve this matter is to restart your wireless router. Many times, restarting your router fixes this issue. You should reboot your computer too after restarting the router. Also, in some cases, the DHCP server can fail and assign the same IP address to more than one computer. Under this situation, you should try to update your router firmware so issues like this can crop up.

If after trying these solutions you are not able to resolve the issue, you can take the help from our experts. If after trying these solutions you are not able to resolve problem of IP address , you can take the help of our experts.

Instead of using a static IP, go to an automated one

In your settings, you can change from a static IP to an automated one. A static IP means your IP address is set manually, not by your router.

To use an automatic IP:

1) Use your keyboard’s Windows and R keys to press and hold each one. This will bring up the “Run” function.

2) Type in ncpa.cpl and click “OK.” This will open the “Network Connections” window.

3) Choose “Properties” with a right-click on the adapter you’re now using.

4) Double clicking will select “Internet Protocol Version 4 (TCP/IPv4)”.

5) From the “General” tab, select both options to get an IP and DNS server addresses automatically.”

6) Click “OK” on both windows and restart your computer.